BPI-CM9-Linux/build/patch/kernel/archive/sunxi-6.18/dt_32/sun8i-h2-plus-sunvell-r69.dts

// SPDX-License-Identifier: (GPL-2.0+ or MIT)
/*
 * Based original Sunvell R69 FEX file (2019 karabek)
 */

/dts-v1/;
#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>

/ {
	model = "Sunvell R69";
	compatible = "sunvell,sunvell-r69", "allwinner,sun8i-h2-plus";

	aliases {
		ethernet0 = &emac;
		ethernet1 = &xr819;
		serial0 = &uart0;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	connector {
		compatible = "hdmi-connector";
		type = "a";

		port {
			hdmi_con_in: endpoint {
				remote-endpoint = <&hdmi_out_con>;
			};
		};
	};

	leds {
		compatible = "gpio-leds";
		pinctrl-names = "default";
		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;

		pwr_led {
			label = "sunvell-r69:red:pwr";
			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
		};

		status_led {
			label = "sunvell-r69:blue:status";
			gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
			linux,default-trigger = "heartbeat";
		};
	};

	reg_vdd_cpux: vdd-cpux-regulator {
		compatible = "regulator-gpio";
		regulator-name = "vdd-cpux";
		regulator-type = "voltage";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <1100000>;
		regulator-max-microvolt = <1300000>;
		regulator-ramp-delay = <50>;		/* 4ms */

		gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>;	/* PL6 */
		enable-active-high;
		gpios-states = <0x1>;
		states = <1100000 0x0
			  1300000 0x1>;
	};

	reg_vcc_wifi: reg_vcc_wifi {
		compatible = "regulator-fixed";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-name = "vcc-wifi";
		gpio = <&r_pio 0 7 GPIO_ACTIVE_HIGH>;
	        startup-delay-us = <70000>;
		enable-active-high;
	};

	wifi_pwrseq: wifi_pwrseq {
		compatible = "mmc-pwrseq-simple";
		reset-gpios = <&r_pio 0 0 GPIO_ACTIVE_LOW>;
		post-power-on-delay-ms = <200>;
	};
};

&cpu0 {
	cpu-supply = <&reg_vdd_cpux>;
};

&de {
	status = "okay";
};

&ehci0 {
	status = "okay";
};

&ehci1 {
	status = "okay";
};

&emac {
	phy-handle = <&int_mii_phy>;
	phy-mode = "mii";
	allwinner,leds-active-low;
	status = "okay";
};

&hdmi {
	status = "okay";
};

&hdmi_out {
	hdmi_out_con: endpoint {
		remote-endpoint = <&hdmi_con_in>;
	};
};

&ir {
	pinctrl-names = "default";
	pinctrl-0 = <&r_ir_rx_pin>;		/* <&r_ir_rx_pin> */
	status = "okay";
};

&mmc0 {
	vmmc-supply = <&reg_vcc3v3>;
	bus-width = <4>;
	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
	status = "okay";
};

&mmc1 {
	vmmc-supply = <&reg_vcc_wifi>;
	mmc-pwrseq = <&wifi_pwrseq>;
	bus-width = <4>;
	non-removable;
	status = "okay";

	xr819: sdio_wifi@1 {
		reg = <1>;
		compatible = "xradio,xr819";
		interrupt-parent = <&pio>;
		interrupts = <0 11 IRQ_TYPE_EDGE_RISING>;
		interrupt-names = "host-wake";
	};
};

&mmc2 {
	pinctrl-names = "default";
	pinctrl-0 = <&mmc2_8bit_pins>;
	vmmc-supply = <&reg_vcc3v3>;
	bus-width = <8>;
	non-removable;
	cap-mmc-hw-reset;
	status = "okay";
};

&mmc2_8bit_pins {
	/* Increase current from 30mA to 40mA for DDR eMMC */
	allwinner,drive = <SUN4I_PINCTRL_40_MA>;
};

&ohci0 {
	status = "okay";
};

&ohci1 {
	status = "okay";
};

&pio {
	leds_opc: led_pins {
		pins = "PA15";
		function = "gpio_out";
	};
};

&r_pio {
	leds_r_opc: led_pins {
		pins = "PL10";
		function = "gpio_out";
	};
};

&reg_usb0_vbus {
	gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>;	/* PL2 */
	status = "okay";
};

&uart0 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart0_pa_pins>;
	status = "okay";
};

&uart1 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart1_pins>;
	status = "disabled";
};

&uart2 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart2_pins>;
	status = "disabled";
};

&uart3 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart3_pins>;
	status = "disabled";
};

&usb_otg {
	dr_mode = "host";
	status = "okay";
};

&usbphy {
	status = "okay";
};