101 lines
2.5 KiB
Diff
101 lines
2.5 KiB
Diff
From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001
|
|
From: "Miouyouyou (Myy)" <[email protected]>
|
|
Date: Mon, 5 Nov 2018 21:58:56 +0100
|
|
Subject: ARM: DTS: rk3288-tinker: Enabling SDIO and Wifi
|
|
|
|
Adding the appropriate nodes in order to exploit the WiFi capabilities
|
|
of the board.
|
|
Since these capabilities are provided through SDIO, and the SDIO
|
|
nodes were not defined, these were added too.
|
|
|
|
These seems to depend on each other so they are added in one big
|
|
patch.
|
|
|
|
Split if necessary.
|
|
|
|
Signed-off-by: Miouyouyou (Myy) <[email protected]>
|
|
---
|
|
arch/arm/boot/dts/rockchip/rk3288-tinker.dts | 62 ++++++++++
|
|
1 file changed, 62 insertions(+)
|
|
|
|
diff --git a/arch/arm/boot/dts/rockchip/rk3288-tinker.dts b/arch/arm/boot/dts/rockchip/rk3288-tinker.dts
|
|
index 111111111111..222222222222 100644
|
|
--- a/arch/arm/boot/dts/rockchip/rk3288-tinker.dts
|
|
+++ b/arch/arm/boot/dts/rockchip/rk3288-tinker.dts
|
|
@@ -6,10 +6,72 @@
|
|
/dts-v1/;
|
|
|
|
#include "rk3288-tinker.dtsi"
|
|
+#include <dt-bindings/clock/rockchip,rk808.h>
|
|
|
|
/ {
|
|
model = "Rockchip RK3288 Asus Tinker Board";
|
|
compatible = "asus,rk3288-tinker", "rockchip,rk3288";
|
|
+
|
|
+ /* This is essential to get SDIO devices working.
|
|
+ The Wifi depends on SDIO ! */
|
|
+ sdio_pwrseq: sdio-pwrseq {
|
|
+ compatible = "mmc-pwrseq-simple";
|
|
+ clocks = <&rk808 RK808_CLKOUT1>;
|
|
+ clock-names = "ext_clock";
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&chip_enable_h>, <&wifi_enable_h>;
|
|
+
|
|
+ /*
|
|
+ * On the module itself this is one of these (depending
|
|
+ * on the actual card populated):
|
|
+ * - SDIO_RESET_L_WL_REG_ON
|
|
+ * - PDN (power down when low)
|
|
+ */
|
|
+ reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>, <&gpio4 27 GPIO_ACTIVE_LOW>;
|
|
+ };
|
|
+
|
|
+ wireless-wlan {
|
|
+ compatible = "wlan-platdata";
|
|
+ rockchip,grf = <&grf>;
|
|
+ sdio_vref = <1800>;
|
|
+ status = "okay";
|
|
+ wifi_chip_type = "8723bs";
|
|
+ WIFI,host_wake_irq = <&gpio4 30 GPIO_ACTIVE_HIGH>;
|
|
+ };
|
|
+};
|
|
+
|
|
+&io_domains {
|
|
+ wifi-supply = <&vcc_18>;
|
|
+};
|
|
+
|
|
+&pinctrl {
|
|
+ sdio-pwrseq {
|
|
+ wifi_enable_h: wifienable-h {
|
|
+ rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
+ };
|
|
+
|
|
+ chip_enable_h: chip-enable-h {
|
|
+ rockchip,pins = <4 27 RK_FUNC_GPIO &pcfg_pull_none>;
|
|
+ };
|
|
+ };
|
|
+};
|
|
+
|
|
+&sdio0 {
|
|
+ bus-width = <4>;
|
|
+ cap-sd-highspeed;
|
|
+ cap-sdio-irq;
|
|
+ clock-frequency = <50000000>;
|
|
+ clock-freq-min-max = <200000 50000000>;
|
|
+ disable-wp;
|
|
+ keep-power-in-suspend;
|
|
+ mmc-pwrseq = <&sdio_pwrseq>;
|
|
+ non-removable;
|
|
+ num-slots = <1>;
|
|
+ pinctrl-names = "default";
|
|
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
|
|
+ sd-uhs-sdr104;
|
|
+ status = "okay";
|
|
+ supports-sdio;
|
|
};
|
|
|
|
&uart0 {
|
|
--
|
|
Armbian
|
|
|